About possibility of using the method of diesel cranking with external power source to evaluate the friction of piston rings

This study investigates the applicability of diesel cranking with an external power source for evaluating piston ring friction. Experiments were conducted on an air-cooled 2Ch10.5/12 diesel engine with a nominal power of 22  kW. The temperatures of the motor oil in the crankcase and of the ambient air were maintained constant at 85 ±  1 °C and 30 ± 1 °C, respectively. Mechanical losses were evaluated by two methods: 1) diesel cranking with an external power source and 2) comparison of indicated and effective powers at 30 % of nominal engine load. Mineral oils I-20A, MS-20, as well as their mixtures, were used as motor oils during testing. Mechanical losses determined by diesel cranking with an electric motor were approximately 16 % lower than those determined by comparison of indicated and effective powers. Assuming that the major fraction of the reduction in mechanical losses is caused by a lower force pressing the piston rings against the cylinder wall, the friction coefficients of the piston rings were calculated. The obtained friction coefficient values exceeded those reported in scientific literature by more than five times. This indicates that the change in piston ring friction is not the main cause of the reduction in mechanical losses during the transition from motor operation to diesel cranking. Therefore, piston ring friction cannot be determined by comparing mechanical losses obtained in cranking and motor regimes. An analysis of the causes of the reduction in mechanical losses during the transition from motor operation to diesel cranking was carried out.

1. Erofeev, V. L., V. A. Zhukov, O. V. Mel’nik. et al. Upravlenie energoeffektivnost’yu ob»ektov morskoy tekhniki i sudovykh dvigateley vnutrennego sgoraniya. Sankt- Peterburg: Federal’noe gosudarstvennoe byudzhetnoe obrazovatel’noe uchrezhdenie vysshego obrazovaniya Gosudarstvennyy universitet morskogo i rechnogo flota im. admirala S. O. Makarova, 2018: 184.

2. Khannanov, M. D., I. F. Gumerov, L. I. Fardeev, A. S. Kulikov and E. R. Alimgulov “The experimental study of mechanical losses in the modern diesel engine”. Tractors and Agricultural Machinery. 89.3 (2022):187–195. DOI: https://doi.org/10.17816/0321-4443-106271.

3. Wakuri, Y., T. Hamatake, M. Soejima and T. Kitahara. “Piston ring friction in internal combustion engines.” Tribology International 25.5 (1992): 299–308. DOI: 10.1016/0301–679X(92)90027-K.

4. Gangopadhyay, A. “A Review of Automotive Engine Friction Reduction Opportunities Through Technologies Related to Tribology.” Transactions of the Indian Institute of Metals 70.2 (2017): 527–535.

5. Kumar, R., S. Sambhav, P. R. Yadav, Md S. Ansari, A. Ansari, M. Ansari and S. Kumar “Experimental and Simulation Study of Piston Ring Pack Influence on Heat Transfer and Friction”. International Journal of Advanced Research in Science, Communication and Technology 5.11 (2025): 106–110. DOI: 10.48175/IJARSCT-27212.

6. Delprete, C. and A. Razavykia. “Piston ring–liner lubrication and tribological performance evaluation: A review.” Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology 232.2 (2018): 193–209. DOI: 10.1177/1350650117706269.

7. Rudnev, B. I. and O. V. Povalikhina. “Calculation- experimental definition of coefficient friction of piston rings in marine.” Aktual’nye problemy osvoeniya biologicheskikh resursov Mirovogo okeana: Materialy VIII Mezhdunarodnoy nauchno- tekhnicheskoy konferentsii, Vladivostok, 23–24 maya 2024 goda. Vladivostok: Dal’nevostochnyy gosudarstvennyy tekhnicheskiy rybokhozyaystvennyy universitet, 2024: 312–316. DOI: 10.48612/dalrybvtuz/mntk-wo-2024-32.

8. Nikolopoulou, V–I., A. Zavos and P. Nikolakopoulos. “A Comparative Analysis of Friction and Energy Losses in Hydrogen and CNG Fueled Engines: Implications on the Top Compression Ring Design Using Steel, Cast Iron, and Silicon Nitride Materials.” Materials 17.15 (2024). DOI: 10.3390/ma17153806.

9. Liu, N., P. Liu et al. “Simulation on the effect of cylinder liner and piston ring surface roughness on friction performance.” Mechanics & Industry 23 (2022): 8. DOI: 10.1051/meca/2022007.

10. Dellis, P. “Comparative Research in the Field of the Parametric Effect of Lubricant Cavitation Initiation and Development on Friction and Wear in Piston Ring and Cylinder Liner Assemblies.” Lubricants 12.12 (2024). DOI: 10.3390/lubricants12120460.

11. Stefanovskiy, B. S., E. A. Skobtsev and E. K. Korsi i dr. Ispytaniya dvigateley vnutrennego sgoraniya. M: Mashinostroenie, 1972: 368.

12. Tsvetkov, Yu. N., A. A. Tatulyan, V. N. Kuz’min and D. A. Krylov. “Diesel testbed to test lubricants.” Zhurnal universiteta vodnykh kommunikatsiy 3 (2011): 57–66.

13. Tsvetkov, Yu. N., D. A. Krylov and A. A. Tatulyan. “Sootnoshenie poter’ na trenie, prikhodyaschikhsya na granichnyy i gidrodinamicheskiy rezhimy smazki, v dvigatelyakh vnutrennego sgoraniya.” Engines Construction 1(239) (2010): 13–19.

14. Myshkin, N. K. and M. I. Petrokovets. Tribologiya. Printsipy i prilozheniya. Gomel’: IMMS NANB, 2002: 310.

15. Du, C., C. Sheng, X. Liang, X. Rao and Z. Guo “Effects of Temperature on the Tribological Properties of Cylinder- Liner Piston Ring Lubricated with Different Oils” Lubricants 11(3) (2023): 1–17. DOI: 10.3390/lubricants11030115.

16. Mur, D. Osnovy i primeneniya tribonikiOsnovy i primeneniya triboniki. L: Mir, 1978: 487..

17. Englisch, C. Kolbenringe. Band 1: Theorie, Herstellung und Bemessung. Wien: Springer- Verlag, 1958.

18. Lukanin, V. N., B. Ya. Chernyak i dr. et al. Dvigateli vnutrennego sgoraniya. V 3-kh kn. Kn. 1. Teoriya rabochikh protsessov. M: Vysshaya shkola, 2007: 479.

19. Zakharov, S. M., A. P. Ni-kitin and Yu. A. Zagoryanskiy. Podshipniki kolenchatykh valov teplovoznykh dizeley. M: Transport, 1981: 179.

20. Surkin, V. I. and B. V. Kurchatov. Smazka par treniya dizeley. Chelyabinsk: Chelyabinskiy gosudarstvennyy agroinzhenernyy universitet, 1999: 224.